Hat Top Airflow Ridgevent

Hat Top Airflow Ridgevent with two louvers exhaust plate parallel to roof slope with Hat type cavity Ridge of colour coated galvanise, Colour coated Galvalume, and galvalume as per the customer’s requirement. Hat top Airflow Ridgevent is easy to install at all Roof profile design and on old existing profile and maintenance free with long performance life cycle.


» Continuous High natural airflow
» Supply in 5 meters of Airflow ridgevent is equivalent to 2 whirlybird
» Internal pressure of structures decreased.
» Eliminates foam closures failure
» Available in Colour coated steel and all roofing profiles
» Improves & maintains a comfortable living environment
» No power, moving parts, or noise
» Maintenance-free (No clogging)
» Maintains a clean, attractive roofline – hidden underneath louvers ridge cap
» Extends the life of the building through natural air circulation
» Actively prevents the build-up of mould within the ceiling cavity – numerous health benefits
» Located precisely where they do the most good, at the peak of the roof, Airflow Ridgevent are virtually invisible from ground level and they provide greater airflow than other vents
» Easy to install on existing old roofing ALSO
» Maximum effective utilisation of space with an existing arrangement of structure.
» Made in INDIA

Hat Top Airflow Ridgevent

Turbo ventilators

Installed at the apex portion of the roof, Located precisely where they do the most good NO puncturing or cutting sheets in between roof slope

For installation puncturing or cutting sheets in between the roof slope is required

Simple to install no leakage issues

Failure of workmanship can result in leakage  

No rotating parts has Long durable life and effective performance

Self-weight that require wind to make them effective. These moving parts inevitably wear out

Maintains a clean, attractive roofline for all types of industrial building

Projected conical dome in between roofline

Easy to install at all Roof profile design and on an old existing profile

Turbo base need matching roof profile design

Best for planning solar panel installation in future, Due to its ideal peak installation position

Puncture the roof slope at regular intervals create a hurdle in the future for solar panel installation planning and cause of leakage

Maintenance-free with long performance life cycle

Due to rotating parts and FRP or polycarbonate base require maintenances and monitoring

Maintains a clean, attractive roofline – hidden underneath louvers ridge cap

Patch-wise dome section in the middle of roof slope

Low volume less transportation cost, additional saving No ridge flashing required

High volume more transportation cost 

Can perform in high wind area

May be vulnerable to topple over in high windy area

Fast and easy installation with throughout ridge length ventilation

Installation takes more time and costly  with patch wise ventilation

Best For high rise industrial building

Maintenance or performance failure can be a big issue

“Ventilation should never be an afterthought in constructing a factory building, Your building needs to breathe”


Hat Type Airflow ridgevent
Hat Type Air flow ridgevent
Hat Top Air flow ridgevent installation
substitute to turbo ventilator
turbo ventilator substitute airflow ridgevent

» Ensure roof sheeting is straight with no steps between roof sheets before installation of Airflow ridgevent of louver plate, especially regarding hip cut sheets. Maintain a minimum 100mm to maximum 150mm gap between sheet ends.
» Roof sheets are NOT to be turned up
» Slide louver plate over the end of the sheet until in correct position
» Starting from the left end pull down firmly on the louver plate install with a metal self-tapping self-drilling screw through the top row of louver plate to hold in place
» On the right end pull down firmly on the louver plate, install with metal self-tapping screw drilling through the top row of louver plate to secure in place
» Install STSD screws in the bottom row of louver plate directly below top screws to ensure installation (each piece must have evenly spaced screws) as per manufacturer’s recommendations, seal right side join with silicon sealant for a complete seal
» Slide next airflow Ridgevent louver plate on an angle overlapping the previous louver plate until locked into place, pull down firmly and install 19mm/ 25mm screw/ rivet and continue as per previous steps (each piece must have eight screws) where joins do not meet on a sheet rib secure with two screws
» Continue to install each Airflow Ridgvent louver plate on both sides of top ridge and hips where required
» Install ridge cap over fitted Airflow Ridgevent louver plate and secure to either batten or every second roof sheet rib.


» Do not turn up the sheets. For roofs with a pitch of under 4 degrees, please contact the manufacturer for installation instructions.
» When laying the roof sheets, please ensure the sheets are laid straight.
» Silicon all joins, in particular ensuring that there is no gap
» Always follow the manufacturer screw pattern guidelines.
» The throat gap between the Air Flow Ridge vent louvers is recommended to be minimum 75mm minimum.
» For retro-fit installations, previous screw holes are to be sealed for waterproofing.

“Airflow Ridgevent located precisely where they do the most good”